FAG 1302-C3 Self-Aligning Bearing, Double Row, Open, Steel Cage, C3 Clearance, Metric, 15mm ID, 42mm OD, 13mm Width, NULL Maximum Rotaional Speed

FAG 1302-C3 Self-Aligning Bearing, Double Row, Open, Steel Cage, C3 Clearance, Metric, 15mm ID, 42mm OD, 13mm Width, NULL Maximum Rotaional Speed

Product Description

This FAG double-row self-aligning ball bearing is an open bearing, and has a cylindrical bore, steel cage, and C3 clearance rating. It is suitable for applications supporting moderate radial loads and moderate to low thrust loads. This bearing has concave sphered housing rings to compensate for static angular misalignments between the shaft and housing in applications subject to shaft deflections or mounting errors. Because this bearing type has the lowest operational friction of all rolling bearings, it runs cool at high speeds. This bearing is made of low-alloy, through-hardened chromium steel for durability and resistance to deformity under heavy loads. The bearing has a straight bore for fitting on a conventional cylindrical shaft. Its open design facilitates lubricating the bearing in place and dissipating heat. This bearing has a steel cage to prevent the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. Additionally, this bearing is produced to PN (normal) tolerances in accordance with Deutsches Institut für Normung (DIN) 620-2 standards for quality assurance. This self-aligning ball bearing is for use in commercial and industrial applications including film processing equipment, office automation, vertical spinning equipment, and industrial countershafts, among others.

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Self-aligning bearing for applications subject to shaft deflections or misalignments between the shaft and housing
  • Straight bore for fitting on a conventional cylindrical shaft
  • Open configuration for lubrication applied in place
  • Steel cage evenly spaces balls for reduced friction, vibration, and noise
  • C3 radial internal clearance is larger than normal allowing for thermal expansion
Specifications for this item
Brand Name FAG Bearings
Part Number 1302-C3
System of Measurement Metric
Bore Diameter 15  mm
Outside Diameter 42  mm
Overall Width 13  mm
EAN 4012801159210
Number of Items 1
UNSPSC Code 31171504
FAG 6215-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 75mm ID, 130mm OD, 25mm Width, 4800rpm Maximum Rotational Speed, 11000lbf Static Load Capacity, 14900lbf Dynamic Load Capacity

FAG 6215-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 75mm ID, 130mm OD, 25mm Width, 4800rpm Maximum Rotational Speed, 11000lbf Static Load Capacity, 14900lbf Dynamic Load Capacity

Product Description

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a metal shield on either side that is fastened to the outside ring and extends over the rolling elements. The shields assist in keeping out contaminants such as dirt and grime and also help to hold in lubricant applied during manufacturing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Product Features

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Light” bearing design for use in limited space applications or for average loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Metal shields on both sides of the bearing keep the lubricant in and contaminants out
Specifications for this item
Brand Name FAG Bearings
Part Number 6215-2Z-C3
Material Type Steel
System of Measurement Metric
Bore Diameter 75  mm
Outside Diameter 130  mm
Overall Width 25  mm
Max Rotational Speed 5600  RPM
Static Load Capacity 14900  pounds
Dynamic Load Capacity 11000  pounds
Specification Met DIN 620-4/DIN 623-1/DIN 625-1/DIN ISO 281/EN 10139/ISO 281/ISO 286/ISO 683-17/SAE J403
EAN 4012801203425
Number of Items 1
UNSPSC Code 31171504
FAG 6318-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 90mm ID, 190mm OD, 43mm Width, 3400 rpm Maximum Rotational Speed, 22800 lbf Static Load Capacity, 30000 lbf Dynamic Load Capacity

FAG 6318-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 90mm ID, 190mm OD, 43mm Width, 3400 rpm Maximum Rotational Speed, 22800 lbf Static Load Capacity, 30000 lbf Dynamic Load Capacity

Product Description

This FAG Medium 6300 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Medium,” making it applicable for use with average to above average radial loads and light to average axial loads. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a metal shield on either side that fastens to the outside ring and extends over the rolling elements. The shields help keep out contaminants such as dirt and grime and also help to hold in lubricant applied during manufacturing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Product Features

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Medium” bearing design for average to above average radial loads and light to average axial loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Metal shields on both sides of the bearing keep the lubricant in and contaminants out
Specifications for this item
Brand Name FAG Bearings
Part Number 6318-2Z-C3
Material Type Steel
System of Measurement Metric
Bore Diameter 90  mm
Outside Diameter 190  mm
Overall Width 43  mm
Max Rotational Speed 3400  RPM
Static Load Capacity 30000  pounds
Dynamic Load Capacity 22800  pounds
Specification Met DIN 620-4/DIN 623-1/DIN 625-1/DIN ISO 281/EN 10139/ISO 281/ISO 286/ISO 683-17/SAE J403
EAN 4012801205863
Item Weight 11.82 pounds
Number of Items 1
UNSPSC Code 31171504
FAG 2211-2RS-TV Self-Aligning Bearing, Double Row, Double Sealed, Polyamide/Nylon Cage, Normal Clearance, Metric, 55mm ID, 100mm OD, 25mm Width, 4800rpm Maximum Rotaional Speed, 2240lbf Static Load Capacity, 6000lbf Dynamic Load Capacity

FAG 2211-2RS-TV Self-Aligning Bearing, Double Row, Double Sealed, Polyamide/Nylon Cage, Normal Clearance, Metric, 55mm ID, 100mm OD, 25mm Width, 4800rpm Maximum Rotaional Speed, 2240lbf Static Load Capacity, 6000lbf Dynamic Load Capacity

Product Description

This FAG double-row self-aligning ball bearing is double-sealed, and has a cylindrical bore, polyamide/nylon cage, and normal clearance rating. It is suitable for applications supporting moderate radial loads and moderate to low thrust loads. This bearing has concave sphered housing rings to compensate for static angular misalignments between the shaft and housing in applications subject to shaft deflections or mounting errors. Because this bearing type has the lowest operational friction of all rolling bearings, it runs cool at high speeds. This bearing is made of low-alloy, through-hardened chromium steel for durability and resistance to deformity under heavy loads. The bearing has a straight bore for fitting on a conventional cylindrical shaft. Contact seals on both sides of the bearing keep out contaminants such as dirt and grime and hold in lubricant applied at manufacturing that lasts the lifetime of the bearing. This bearing has an injection-molded snap-type cage made of glass fiber reinforced polyamide 66 to prevent the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This cage type can be used at operating temperatures up to 120 degrees C (250 degrees F). The bearing has a normal radial internal clearance designation, making it suitable for applications where the load and speeds do not result in thermal expansion. This clearance provides latitude for self-realignment and compensates for static and dynamic alignment errors. Additionally, this bearing is produced to PN (normal) tolerances in accordance with Deutsches Institut für Normung (DIN) 620-2 standards for quality assurance. This self-aligning ball bearing is for use in commercial and industrial applications including film processing equipment, office automation, vertical spinning equipment, and industrial countershafts, among others.

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Self-aligning bearing for applications subject to shaft deflections or misalignments between the shaft and housing
  • Straight bore for fitting on a conventional cylindrical shaft
  • Contact seals on both sides of the bearing keeps lubricant in and contaminants out
  • Glass fiber reinforced polyamide 66 plastic cage evenly spaces balls for reduced friction, vibration, and noise
  • Normal radial internal clearance for applications where thermal expansion is not a factor
Specifications for this item
Brand Name FAG Bearings
Part Number 2211-2RS-TVH
System of Measurement Metric
Bore Diameter 55  mm
Outside Diameter 100  mm
Overall Width 25  mm
Max Rotational Speed 4800  RPM
Static Load Capacity 2240  pounds
Dynamic Load Capacity 6000  pounds
EAN 4012801160537
Item Weight 1.79 pounds
Number of Items 1
UNSPSC Code 31171504
FAG 54306 Double Direction Self-Aligning Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 25mm ID, 60mm OD, 41.3mm Width, 4000rpm Maximum Rotational Speed, 14600lbf Static Load Capacity, 8500lbf Dynamic Load Capacity

FAG 54306 Double Direction Self-Aligning Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 25mm ID, 60mm OD, 41.3mm Width, 4000rpm Maximum Rotational Speed, 14600lbf Static Load Capacity, 8500lbf Dynamic Load Capacity

Product Description

This FAG self-aligning, double-direction thrust ball bearing has a 90-degree contact angle, a double row of balls, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two spherical housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with spherical-shaped housing washers that help compensate for static angular misalignments between the shaft and housing. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 54306
System of Measurement Metric
Bore Diameter 25  mm
Outside Diameter 60  mm
Overall Width 41.3  mm
Max Rotational Speed 4000  RPM
Static Load Capacity 14600  pounds
Dynamic Load Capacity 8500  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801163224
Number of Items 1
UNSPSC Code 31171552
FAG 53203 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 17mm ID, 35mm OD, 13.2mm Width, 6700rpm Maximum Rotational Speed, 6100lbf Static Load Capacity, 3900lbf Dynamic Load Capacity

FAG 53203 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 17mm ID, 35mm OD, 13.2mm Width, 6700rpm Maximum Rotational Speed, 6100lbf Static Load Capacity, 3900lbf Dynamic Load Capacity

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53203
System of Measurement Metric
Bore Diameter 17  mm
Outside Diameter 35  mm
Overall Width 13.2  mm
Max Rotational Speed 6700  RPM
Static Load Capacity 6100  pounds
Dynamic Load Capacity 3900  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162883
Number of Items 1
UNSPSC Code 31171552
FAG 51216 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 80mm ID, 115mm OD, 28mm Width, 2600rpm Maximum Rotational Speed, 43000lbf Static Load Capacity, 17000lbf Dynamic Load Capacity

FAG 51216 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 80mm ID, 115mm OD, 28mm Width, 2600rpm Maximum Rotational Speed, 43000lbf Static Load Capacity, 17000lbf Dynamic Load Capacity

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51216
System of Measurement Metric
Bore Diameter 80  mm
Outside Diameter 115  mm
Overall Width 28  mm
Max Rotational Speed 2600  RPM
Static Load Capacity 43000  pounds
Dynamic Load Capacity 17000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801197946
Item Weight 2.09 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 52320 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 85mm ID, 170mm OD, 97mm Width, 1600rpm Maximum Rotational Speed, 127000lbf Static Load Capacity, 52000lbf Dynamic Load Capacity

FAG 52320 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 85mm ID, 170mm OD, 97mm Width, 1600rpm Maximum Rotational Speed, 127000lbf Static Load Capacity, 52000lbf Dynamic Load Capacity

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52320
System of Measurement Metric
Bore Diameter 85  mm
Outside Diameter 170  mm
Overall Width 97  mm
Max Rotational Speed 1600  RPM
Static Load Capacity 127000  pounds
Dynamic Load Capacity 52000  pounds
Specification Met DIN 623-1 , ISO 281 , ISO 683-17 , ISO 199 , DIN ISO 281 , EN 10139 , SAE J403
EAN 4012801322461
Item Weight 19.64 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 52204 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 15mm ID, 40mm OD, 26mm Width, 5600rpm Maximum Rotational Speed, 8500lbf Static Load Capacity, 5000lbf Dynamic Load Capacity

FAG 52204 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 15mm ID, 40mm OD, 26mm Width, 5600rpm Maximum Rotational Speed, 8500lbf Static Load Capacity, 5000lbf Dynamic Load Capacity

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52204
System of Measurement Metric
Bore Diameter 15  mm
Outside Diameter 40  mm
Overall Width 26  mm
Max Rotational Speed 5600  RPM
Static Load Capacity 8500  pounds
Dynamic Load Capacity 5000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162609
Number of Items 1
UNSPSC Code 31171552
FAG 52220 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 85mm ID, 150mm OD, 67mm Width, 1900rpm Maximum Rotational Speed, 72000lbf Static Load Capacity, 27500lbf Dynamic Load Capacity

FAG 52220 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 85mm ID, 150mm OD, 67mm Width, 1900rpm Maximum Rotational Speed, 72000lbf Static Load Capacity, 27500lbf Dynamic Load Capacity

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52220
System of Measurement Metric
Bore Diameter 85  mm
Outside Diameter 150  mm
Overall Width 67  mm
Max Rotational Speed 1900  RPM
Static Load Capacity 72000  pounds
Dynamic Load Capacity 27500  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801016964
Number of Items 1
UNSPSC Code 31171552