Bearing FAG

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6002-2RSR-L038-C3

Materi/Bahan: steel

Diameter Lubang: 15  mm

Diameter Luar: 32  mm

Lebar Bearing: 9  mm

Kecepatan Rotasi Maksimum: 28000  RPM

Kapasitas Muatan Statis: 571.5264 kilograms

Kapasitas Muatan Dinamis: 290.753 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Rubber seals on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that is fastened to the outside ring, extends over the rolling elements and makes contact with the inside ring, keeping out contaminants such as dirt and grime. The seals also hold in a high quality lubricant applied during manufacturing that will last the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, inline skates, among others.

Specifications Met

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6301-2RSR-L038-C3

Materi/Bahan: Steel

Diameter Lubang: 12  mm

Diameter Luar: 37  mm

Lebar Bearing: 12  mm

Kecepatan Rotasi Maksimum: 13000  RPM

Kapasitas Muatan Statis: 997.9032 kilograms

Kapasitas Muatan Dinamis: 430.913 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Medium” bearing design for average to above average radial loads and light to average axial loads
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Rubber seals on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Medium 6300 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Medium,” making it applicable for use with average to above average radial loads and light to average axial loads. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that fastens to the outside ring, extends over the rolling elements, and makes contact with the inside ring to keep out contaminants such as dirt and grime. The seals also hold in a lubricant applied during manufacturing that lasts the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6002-C3

Materi/Bahan: steel

Diameter Lubang: 15  mm

Diameter Luar: 32  mm

Lebar Bearing: 9  mm

Kecepatan Rotasi Maksimum: 28000  RPM

Kapasitas Muatan Statis: 571.5264 kilograms

Kapasitas Muatan Dinamis: 290.753 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6006-C3

Materi/Bahan: steel

Diameter Lubang: 30  mm

Diameter Luar: 55  mm

Lebar Bearing: 13  mm

Kecepatan Rotasi Maksimum: 5000  RPM

Kapasitas Muatan Statis: 1356.241 kilograms

Kapasitas Muatan Dinamis: 848.21773 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Merk: FAG Bearings

Nomor/Jenis Sparepart: 6209

Materi/Bahan: steel

Diameter Lubang: 45  mm

Diameter Luar: 85  mm

Lebar Bearing: 19  mm

Kecepatan Rotasi Maksimum: 19000  RPM

Kapasitas Muatan Statis: 2063.845 kilograms

Kapasitas Muatan Dinamis: 3152.467 kilograms

Fitur Produk:

Deskripsi:

The FAG single-row, open radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a CN (normal) radial internal clearance for applications that do not involve thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has an open configuration for lubrication in place and applications involving negligible exposure to dirt, grime, debris, and other contaminants. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions	DIN 715
Basic dynamic load ratings	DIN ISO 281
Dimensional and geometric tolerances	DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart : 6306-C4

Materi/Bahan: steel

Diameter Lubang: 30  mm

Diameter Luar: 72  mm

Lebar Bearing: 19  mm

Kecepatan Rotasi Maksimum: 24000  RPM

Kapasitas Muatan Statis: 1655.612 kilograms

Kapasitas Muatan Dinamis: 2971.03 kilograms

Fitur Produk:

• Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
• Conforms to ABEC 1 precision standard for performance within a narrow range of variation
• C4 radial internal clearance for radial slack between the inner and outer rings is greater than CN (normal) and C3 to compensate for thermal expansion
• Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
• Open bearing for lubrication in place and for use in applications with little exposure to dirt, grime, debris, and other contaminants

Deskripsi:

The FAG single-row, open radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a C4 radial internal clearance for radial slack between the inner and outer rings that is greater than C3 to compensate for thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has an open configuration for lubrication in place and applications involving negligible exposure to dirt, grime, debris, and other contaminants. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions	DIN 715
Basic dynamic load ratings	DIN ISO 281
Dimensional and geometric tolerances	DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6204-2RSR-L038-C3

Materi/Bahan: Steel

Diameter lubang: 20  mm

Diameter Luar:  47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 18000  RPM

Kapasitas Muatan Statis: 1297.27418 kilograms

Kapasitas Muatan Dinamis: 666.7808 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Light” bearing design for use in limited space applications or for average loads
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Rubber seals on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that is fastened to the outside ring, and extends over the rolling elements and to make contact with the inside ring, keeping out contaminants such as dirt and grime. The seals also hold lubricant applied during manufacturing that will last the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6207-C3

Materi/Bahan: Steel

Diameter Lubang: 35  mm

Diameter Luar: 72  mm

Lebar Bearing: 17  mm

Kecepatan Rotasi Maksimum: 11000  RPM

Kapasitas Muatan Statis: 2599.084 kilograms

Kapasitas Muatan Dinamis: 1560.358 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Light” bearing design for use in limited space applications or for average loads
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Open bearing for lubrication applied in place

Deskripsi:

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design allows for lubricating the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6204-2RSR-L038

Materi/Bahan: steel

Diameter Lubang: 20  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 10000  RPM

Kapasitas Muatan Statis: 680.3886 kilograms

Kapasitas Muatan Dinamis: 1315.418 kilograms

Fitur Produk:

• Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
• Conforms to ABEC 1 precision standard for performance within a narrow range of variation
• CN (normal) radial internal clearance for applications that do not involve thermal expansion or atypical precision
• Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
• Rubber seals on both sides of the bearing to keep lubricant in and contaminants out

Deskripsi:

The FAG single-row double-sealed radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a CN (normal) radial internal clearance for applications that do not involve thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has rubber seals on both sides of the bearing to keep lubricant in and contaminants out. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions	DIN 715
Basic dynamic load ratings	DIN ISO 281
Dimensional and geometric tolerances	DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6000-C-C3

Materi/Bahan: steel

Diameter Lubang: 10  mm

Diameter Luar: 26  mm

Lebar Bearing: 8  mm

Kecepatan Rotasi Maksimum: 36000  RPM

Kapasitas Muatan Statis: 471.7361 kilograms

Kapasitas Muatan Dinamis: 200.034 kilograms

Fitur Produk:

• Deep groove geometry for high speeds and supporting both radial and axial loads
• “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
• C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
• Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
• Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions	DIN 625-1
Basic dynamic load ratings	DIN ISO 281
C3 radial internal clearance	DIN 620-4 (ISO 5 753)
Shaft and housing tolerances	ISO 286
Through-hardening steel for inner and outer rings	ISO 683-17
Steel strip for cage	EN 10139, SAE J403
Load carrying capacity and life	DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings	DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.