Bearing

Bearing dalam Bahasa Indonesia berarti bantalan. Dalam ilmu mekanika bearing adalah sebuah elemen mesin yang berfungsi untuk membatasi gerak relatif antara dua atau lebih komponen mesin agar selalu bergerak pada arah yang diinginkan. Bearing menjaga poros (shaft) agar selalu berputar terhadap sumbu porosnya, atau juga menjaga suatu komponen yang bergerak linier agar selalu berada pada jalurnya.

Image result for bearing adalah

Bantalan merupakan salah satu bagian dari elemen mesin yang memegang peranan cukup penting karena fungsi dari bantalan yaitu untuk menumpu sebuah poros agar poros dapat berputar tanpa mengalami gesekan yang berlebihan. Bantalan harus cukup kuat untuk memungkinkan poros serta elemen mesin lainnya bekerja dengan baik.

Bearing atau laher adalah komponen sebagai bantalan untuk membantu mengurangi gesekan peralatan berputar pada poros/as. Bearing atau laher ini biasanya berbentuk bulat. Bearing di mobil dipasang pada as roda dan ditempat-tempat yang berputar lainnya. Tujuan dari bantaran balock untuk mengurangi gesekan rotasi dan mendukung radial dan aksial beban.

 

FAG 51409 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 100mm OD, 39mm Width, 2200rpm Maximum Rotational Speed, 55000lbf Static Load Capacity, 29000lbf Dynamic Load Capacity

FAG 51409 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 100mm OD, 39mm Width, 2200rpm Maximum Rotational Speed, 55000lbf Static Load Capacity, 29000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51409
System of Measurement Metric
Bore Diameter 45  mm
Outside Diameter 100  mm
Overall Width 39  mm
Max Rotational Speed 2200  RPM
Static Load Capacity 55000  pounds
Dynamic Load Capacity 29000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801198370
Item Weight 3.24 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 51320 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 100mm ID, 170mm OD, 55mm Width, 1500rpm Maximum Rotational Speed, 127000lbf Static Load Capacity, 52000lbf Dynamic Load Capacity

FAG 51320 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 100mm ID, 170mm OD, 55mm Width, 1500rpm Maximum Rotational Speed, 127000lbf Static Load Capacity, 52000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51320
System of Measurement Metric
Bore Diameter 100  mm
Outside Diameter 170  mm
Overall Width 55  mm
Max Rotational Speed 1500  RPM
Static Load Capacity 127000  pounds
Dynamic Load Capacity 52000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801321969
Number of Items 1
UNSPSC Code 31171552
FAG 52308 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 30mm ID, 78mm OD, 49mm Width, 3200rpm Maximum Rotational Speed, 25000lbf Static Load Capacity, 13700lbf Dynamic Load Capacity

FAG 52308 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 30mm ID, 78mm OD, 49mm Width, 3200rpm Maximum Rotational Speed, 25000lbf Static Load Capacity, 13700lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52308
System of Measurement Metric
Bore Diameter 30  mm
Outside Diameter 78  mm
Overall Width 49  mm
Max Rotational Speed 3200  RPM
Static Load Capacity 25000  pounds
Dynamic Load Capacity 13700  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162708
Number of Items 1
UNSPSC Code 31171552
FAG 53204 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 20mm ID, 40mm OD, 14.7mm Width, 5600rpm Maximum Rotational Speed, 8500lbf Static Load Capacity, 5000lbf Dynamic Load Capacity

FAG 53204 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 20mm ID, 40mm OD, 14.7mm Width, 5600rpm Maximum Rotational Speed, 8500lbf Static Load Capacity, 5000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53204
System of Measurement Metric
Bore Diameter 20  mm
Outside Diameter 40  mm
Overall Width 14.7  mm
Max Rotational Speed 5600  RPM
Static Load Capacity 8500  pounds
Dynamic Load Capacity 5000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162890
Number of Items 1
UNSPSC Code 31171552
FAG 54305 Double Direction Self-Aligning Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 20mm ID, 52mm OD, 37.6mm Width, 4300rpm Maximum Rotational Speed, 12500lbf Static Load Capacity, 7800lbf Dynamic Load Capacity

FAG 54305 Double Direction Self-Aligning Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 20mm ID, 52mm OD, 37.6mm Width, 4300rpm Maximum Rotational Speed, 12500lbf Static Load Capacity, 7800lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG self-aligning, double-direction thrust ball bearing has a 90-degree contact angle, a double row of balls, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two spherical housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with spherical-shaped housing washers that help compensate for static angular misalignments between the shaft and housing. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 54305
System of Measurement Metric
Bore Diameter 20  mm
Outside Diameter 52  mm
Overall Width 37.6  mm
Max Rotational Speed 4300  RPM
Static Load Capacity 12500  pounds
Dynamic Load Capacity 7800  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801163217
Item Weight 12 ounces
Number of Items 1
UNSPSC Code 31171552
FAG 52410 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 40mm ID, 110mm OD, 78mm Width

FAG 52410 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 40mm ID, 110mm OD, 78mm Width

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52410
System of Measurement Metric
Bore Diameter 40  mm
Outside Diameter 110  mm
Overall Width 78  mm
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801515474
Item Weight 7.85 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 53216 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 80mm ID, 115mm OD, 29.5mm Width, 2600rpm Maximum Rotational Speed, 43000lbf Static Load Capacity, 17000lbf Dynamic Load Capacity

FAG 53216 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 80mm ID, 115mm OD, 29.5mm Width, 2600rpm Maximum Rotational Speed, 43000lbf Static Load Capacity, 17000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53216
System of Measurement Metric
Bore Diameter 80  mm
Outside Diameter 115  mm
Overall Width 29.5  mm
Max Rotational Speed 2600  RPM
Static Load Capacity 43000  pounds
Dynamic Load Capacity 17000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801199322
Item Weight 2.05 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 53206 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 30mm ID, 52mm OD, 17.8mm Width, 4800rpm Maximum Rotational Speed, 10600lbf Static Load Capacity, 5700lbf Dynamic Load Capacity

FAG 53206 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 30mm ID, 52mm OD, 17.8mm Width, 4800rpm Maximum Rotational Speed, 10600lbf Static Load Capacity, 5700lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53206
System of Measurement Metric
Bore Diameter 30  mm
Outside Diameter 52  mm
Overall Width 17.8  mm
Max Rotational Speed 4800  RPM
Static Load Capacity 10600  pounds
Dynamic Load Capacity 5700  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162913
Number of Items 1
UNSPSC Code 31171552
FAG 52217 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 70mm ID, 125mm OD, 55mm Width, 2200rpm Maximum Rotational Speed, 57000lbf Static Load Capacity, 22000lbf Dynamic Load Capacity

FAG 52217 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 70mm ID, 125mm OD, 55mm Width, 2200rpm Maximum Rotational Speed, 57000lbf Static Load Capacity, 22000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52217
System of Measurement Metric
Bore Diameter 70  mm
Outside Diameter 125  mm
Overall Width 55  mm
Max Rotational Speed 2200  RPM
Static Load Capacity 57000  pounds
Dynamic Load Capacity 22000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801198776
Item Weight 5.16 pounds
National Stock Number 3110-01-059-8696
Number of Items 1
UNSPSC Code 31171552
FAG 51314 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 70mm ID, 125mm OD, 40mm Width, 1900rpm Maximum Rotational Speed, 67000lbf Static Load Capacity, 30500lbf Dynamic Load Capacity

FAG 51314 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 70mm ID, 125mm OD, 40mm Width, 1900rpm Maximum Rotational Speed, 67000lbf Static Load Capacity, 30500lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51314
System of Measurement Metric
Bore Diameter 70  mm
Outside Diameter 125  mm
Overall Width 40  mm
Max Rotational Speed 1900  RPM
Static Load Capacity 67000  pounds
Dynamic Load Capacity 30500  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801198233
Item Weight 4.54 pounds
Number of Items 1
UNSPSC Code 31171552