Bearing FAG 6012-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 60mm ID, 95mm OD, 18 mm Wide 8000rpm Maximum Rotational Speed, 5220lbf Static Load Capacity, 6650lbf Dynamic Load Capacity

Bearing FAG 6012-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 60mm ID, 95mm OD, 18 mm Wide 8000rpm Maximum Rotational Speed, 5220lbf Static Load Capacity, 6650lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6012-C3

Materi/Bahan: steel

Diameter Lubang: 60  mm

Diameter Luar: 95  mm

Lebar Bearing: 18  mm

Kecepatan Rotasi Maksimum: 8000  RPM

Kapasitas Muatan Statis: 3016.389 kilograms

Kapasitas Muatan Dinamis: 2367.752 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6305-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 25mm ID, 62mm OD, 17mm Width, 11000 rpm Maximum Rotational Speed, 2600 lbf Static Load Capacity, 5000 lbf Dynamic Load Capacity

Bearing FAG 6305-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 25mm ID, 62mm OD, 17mm Width, 11000 rpm Maximum Rotational Speed, 2600 lbf Static Load Capacity, 5000 lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6305-2Z-L038-C3

Materi/Bahan: steel

Diameter Lubang: 25  mm

Diameter Luar: 62  mm

Lebar Bearing: 17  mm

Kecepatan Rotasi Maksimum: 11000  RPM

Kapasitas Muatan Statis: 2267.962 kilograms

Kapasitas Muatan Dinamis:  1179.34 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Medium” bearing design for average to above average radial loads and light to average axial loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Metal shields on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Medium 6300 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Medium,” making it applicable for use with average to above average radial loads and light to average axial loads. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a metal shield on either side that fastens to the outside ring and extends over the rolling elements. The shields help keep out contaminants such as dirt and grime and also help to hold in lubricant applied during manufacturing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6204RSR-C3 Radial Bearing, Single Row, ABEC 1 Precision, Single Seal, Steel Cage, C3 Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 10000rpm Maximum Rotational Speed, 1500lbf Static Load Capacity, 2900lbf Dynamic Load Capacity

Bearing FAG 6204RSR-C3 Radial Bearing, Single Row, ABEC 1 Precision, Single Seal, Steel Cage, C3 Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 10000rpm Maximum Rotational Speed, 1500lbf Static Load Capacity, 2900lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6204-RSR-C3

Materi/Bahan: steel

Diameter Lubang: 20  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 10000  RPM

Kapasitas Muatan Statis: 680.3886 kilograms

Kapasitas Muatan Dinamis: 1315.418 kilograms

Fitur Produk:

  • Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
  • Conforms to ABEC 1 precision standard for performance within a narrow range of variation
  • C3 radial internal clearance for radial slack between the inner and outer rings is greater than CN (normal) to compensate for thermal expansion
  • Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
  • Rubber seal on the side of the bearing exposed to contaminants and open on the other for applying lubricant

Deskripsi:

The FAG single-row radial bearing with single seal has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a C3 radial internal clearance for radial slack between the inner and outer rings that is greater than CN (normal) to compensate for thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has rubber seals on the side of the bearing to keep lubricant in and contaminants out. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Bearing FAG 6002-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 15mm ID, 32mm OD, 9 mm Wide 16000rpm Maximum Rotational Speed, 641lbf Static Load Capacity, 1260lbf Dynamic Load Capacity

Bearing FAG 6002-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 15mm ID, 32mm OD, 9 mm Wide 16000rpm Maximum Rotational Speed, 641lbf Static Load Capacity, 1260lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6002-2RSR-L038-C3

Materi/Bahan: steel

Diameter Lubang: 15  mm

Diameter Luar: 32  mm

Lebar Bearing: 9  mm

Kecepatan Rotasi Maksimum: 28000  RPM

Kapasitas Muatan Statis: 571.5264 kilograms

Kapasitas Muatan Dinamis: 290.753 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Rubber seals on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that is fastened to the outside ring, extends over the rolling elements and makes contact with the inside ring, keeping out contaminants such as dirt and grime. The seals also hold in a high quality lubricant applied during manufacturing that will last the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6301-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 12mm ID, 37mm OD, 12mm Width, 13000 rpm Maximum Rotational Speed, 950 lbf Static Load Capacity, 2200 lbf Dynamic Load Capacity

Bearing FAG 6301-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 12mm ID, 37mm OD, 12mm Width, 13000 rpm Maximum Rotational Speed, 950 lbf Static Load Capacity, 2200 lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6301-2RSR-L038-C3

Materi/Bahan: steel

Diameter Lubang: 12  mm

Diameter Luar: 37  mm

Lebar Bearing: 12  mm

Kecepatan Rotasi Maksimum: 13000  RPM

Kapasitas Muatan Statis: 997.9032 kilograms

Kapasitas Muatan Dinamis: 430.913 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Medium” bearing design for average to above average radial loads and light to average axial loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Rubber seals on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Medium 6300 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Medium,” making it applicable for use with average to above average radial loads and light to average axial loads. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that fastens to the outside ring, extends over the rolling elements, and makes contact with the inside ring to keep out contaminants such as dirt and grime. The seals also hold in a lubricant applied during manufacturing that lasts the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6002-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 15mm ID, 32mm OD, 9 mm Wide 30000rpm Maximum Rotational Speed, 641lbf Static Load Capacity, 1260lbf Dynamic Load Capacity

Bearing FAG 6002-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 15mm ID, 32mm OD, 9 mm Wide 30000rpm Maximum Rotational Speed, 641lbf Static Load Capacity, 1260lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6002-C3

Materi/Bahan: steel

Diameter Lubang: 15  mm

Diameter Luar: 32  mm

Lebar Bearing:   9 mm

Kecepatan Rotasi Maksimum: 28000  RPM

Kapasitas Muatan Statis: 571.5264 kilograms

Kapasitas Muatan Dinamis: 290.753 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6006-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 30mm ID, 55mm OD, 13 mm Wide 15000rpm Maximum Rotational Speed, 1870lbf Static Load Capacity, 2990lbf Dynamic Load Capacity

Bearing FAG 6006-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 30mm ID, 55mm OD, 13 mm Wide 15000rpm Maximum Rotational Speed, 1870lbf Static Load Capacity, 2990lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6006-C3

Materi/Bahan: steel

Diameter Lubang: 30  mm

Diameter Luar: 55  mm

Lebar Bearing: 13  mm

Kecepatan Rotasi Maksimum: 15000  RPM

Kapasitas Muatan Statis: 1356.241 kilograms

Kapasitas Muatan Dinamis: 848.2177 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6209 Deep Groove Ball Bearing, Single Row, ABEC 1 Precision, Open, Steel Cage, Normal Clearance, Metric, 45mm ID, 85mm OD, 19mm Width, 19000rpm Maximum Rotational Speed, 4550lbf Static Load Capacity, 6950lbf Dynamic Load Capacity

Bearing FAG 6209 Deep Groove Ball Bearing, Single Row, ABEC 1 Precision, Open, Steel Cage, Normal Clearance, Metric, 45mm ID, 85mm OD, 19mm Width, 19000rpm Maximum Rotational Speed, 4550lbf Static Load Capacity, 6950lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6209

Materi/Bahan: steel

Diameter Lubang: 45  mm

Diameter Luar: 85  mm

Lebar Bearing: 19  mm

Kecepatan Rotasi Maksimum: 19000  RPM

Kapasitas Muatan Statis: 2063.8453 kilograms

Kapasitas Muatan Dinamis: 3152.467 kilograms

Fitur Produk:

  • Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
  • Conforms to ABEC 1 precision standard for performance within a narrow range of variation
  • CN (normal) radial internal clearance for applications that do not involve thermal expansion or atypical precision
  • Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
  • Open bearing for lubrication in place and for use in applications with little exposure to dirt, grime, debris, and other contaminants

Deskripsi:

The FAG single-row, open radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a CN (normal) radial internal clearance for applications that do not involve thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has an open configuration for lubrication in place and applications involving negligible exposure to dirt, grime, debris, and other contaminants. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Bearing Nachi 6303-2NSE 17x47x14 Sealed C3 Japan Ball Bearings

Bearing Nachi 6303-2NSE 17x47x14 Sealed C3 Japan Ball Bearings

Bearing Nachi·

Merk: Bearing Nachi

Nomor/Jenis Sparepart: KIT9728

Materi/Bahan: steel

Diameter Lubang: 17  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kapasitas Muatan Statis: 6550  Newtons

Kapasitas Muatan Dinamis: 13600  Newtons

Fitur Produk:

  • Deep groove geometry for supporting both radial and axial loads and high speeds
  • Chrome bearing steel for durability and resistance to deformity under heavy loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 248 degrees F/120 degrees C
  • Rubber seals on both sides to keep lubricant in and contaminants out

Deskripsi:

This Nachi 6303-2NSE ball bearing is made of chrome bearing steel and has rubber seals. It has a 17 mm inside diameter, a 47 mm outside diameter, and a 14 mm depth The bearing has deep groove geometry for supporting both radial and axial loads and high speeds. The races are made of chrome bearing steel for durability and resistance to deformity under heavy loads. The C3 radial clearance allows thermal expansion for continuous operating temperatures up to 248 degrees F/120 degrees C. Rubber seals on both sides of the bearing help retain lubricant and exclude contaminants. The ball is made of chrome bearing steel for strength and resistance to wear and deformation. The static load rating is 6,550 newtons and the dynamic load rating is 13,600 newtons. A steel cage spaces the balls for even load distribution and prevents contact to reduce friction, vibration, and noise. The maximum speed with grease lubrication is 11,000 revolutions per minute (rpm). This deep groove ball bearing is used in applications such as electric motors, compressors, and material handling equipment, among others.

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

Bearing Nachi 6204-2NSE 20x47x14 Sealed C3 Japan Ball Bearings

Bearing Nachi 6204-2NSE 20x47x14 Sealed C3 Japan Ball Bearings

Bearing Nachi·

Merk: Bearing Nachi

Nomor/Jenis Sparepart: KIT9705

Materi/Bahan: steel

Diameter Lubang: 20  mm

Diameter Luar: 7  mm

Lebar Bearing: 14  mm

Kapasitas Muatan Statis: 6600  Newtons

Kapasitas Muatan Dinamis: 12800  Newtons

Fitur Produk:

  • Single-row bearing for supporting radial loads
  • C3 radial internal clearance for radial slack between the inner and outer rings that is greater than CN (normal) to compensate for thermal expansion
  • Sealed to keep lubricant in and contaminants out

Deskripsi:

This 6204-2NSE Nachi bearing is a sealed ball bearing with C3 clearance measuring 20x47x14. This single-row bearing is built to support radial loads. It has C3 radial internal clearance for radial slack between the inner and outer rings that is greater than CN (normal) to compensate for thermal expansion. This bearing is sealed to keep lubricants in and contaminants out.

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.