Bearing Nachi 6203-2NSE 17x40x12 Sealed C3 Japan Ball Bearings

Bearing Nachi 6203-2NSE 17x40x12 Sealed C3 Japan Ball Bearings

Bearing Nachi·

Merk: Bearing Nachi

Nomor/Jenis Sparepart: KIT9704

Diameter Lubang: 17  mm

Diameter Luar: 40  mm

Lebar Bearing: 12  mm

Kapasitas Muatan Statis: 4800 newtons

Kapasitas Muatan Dinamis: 9550 newtons

Fitur Produk:

  • Single-row deep groove geometry for high speeds and supporting both radial and axial loads
  • Chrome steel for durability and resistance to deformity under heavy loads
  • C3 radial internal clearance for radial slack between the inner and outer rings is greater than CN (normal) to compensate for thermal expansion
  • Rubber seals on both sides of the bearing keep the lubricant in and contaminants out
  • Static load rating of 4,800 newtons and dynamic load rating of 9,550 newtons

Deskripsi:

This Nachi 6203-2NSE ball bearing is made of chrome steel, is double sealed, and has C3 internal clearance. It has a 17 mm inside diameter, a 40 mm outside diameter, and a 12 mm depth. This single-row ball bearing has deep groove geometry for applications that require high speeds and support both radial and axial loads. This bearing is made of chrome steel for durability and resistance to deformity under heavy loads. It has C3 radial internal clearance for radial slack between the inner and outer rings is greater than CN (normal) to compensate for thermal expansion. Rubber seals on both sides of the bearing keep the lubricant in and contaminants out. The static load rating is 4,800 newtons and the dynamic load rating is 9,550 newtons. A steel cage spaces the balls for even load distribution and prevents contact to reduce friction, vibration, and noise. The maximum speed with grease lubrication is 12,000 revolutions per minute (rpm). This deep groove ball bearing is suitable for use in applications such as transmissions, motors, and pumps.

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

Bearing FAG 6306-C4 Radial Bearing, Single Row, ABEC 1 Precision, Open, Steel Cage, C4 Clearance, Metric, 30mm ID, 72mm OD, 19mm Width, 24000rpm Maximum Rotational Speed, 3650lbf Static Load Capacity, 6550lbf Dynamic Load Capacity

Bearing FAG 6306-C4 Radial Bearing, Single Row, ABEC 1 Precision, Open, Steel Cage, C4 Clearance, Metric, 30mm ID, 72mm OD, 19mm Width, 24000rpm Maximum Rotational Speed, 3650lbf Static Load Capacity, 6550lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6306-C4

Materi/Bahan: steel

Diameter Lubang: 30  mm

Diameter Luar: 72  mm

Lebar bearing: 19  mm

Kecepatan Rotasi Maksimum: 24000  RPM

Kapasitas Muatan Statis: 1655.612 kilograms

Kapasitas Muatan Dinamis: 2971.03 kilograms

Fitur Produk:

  • Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
  • Conforms to ABEC 1 precision standard for performance within a narrow range of variation
  • C4 radial internal clearance for radial slack between the inner and outer rings is greater than CN (normal) and C3 to compensate for thermal expansion
  • Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
  • Open bearing for lubrication in place and for use in applications with little exposure to dirt, grime, debris, and other contaminants

Deskripsi:

The FAG single-row, open radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a C4 radial internal clearance for radial slack between the inner and outer rings that is greater than C3 to compensate for thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has an open configuration for lubrication in place and applications involving negligible exposure to dirt, grime, debris, and other contaminants. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Bearing FAG 6204-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 10000rpm Maximum Rotational Speed, 1470lbf Static Load Capacity, 2860lbf Dynamic Load Capacity

Bearing FAG 6204-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 10000rpm Maximum Rotational Speed, 1470lbf Static Load Capacity, 2860lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart:  6204-2RSR-L038-C3

Materi/Bahan: steel

Diameter Lubang: 20  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 18000  RPM

Kapasitas Muatan Statis: 1297.274 kilograms

Kapasitas Muatan Dinamis: 666.7808 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Light” bearing design for use in limited space applications or for average loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Rubber seals on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that is fastened to the outside ring, and extends over the rolling elements and to make contact with the inside ring, keeping out contaminants such as dirt and grime. The seals also hold lubricant applied during manufacturing that will last the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6207-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 35mm ID, 72mm OD, 17mm Width, 24000rpm Maximum Rotational Speed, 3440lbf Static Load Capacity, 5730lbf Dynamic Load Capacity

Bearing FAG 6207-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 35mm ID, 72mm OD, 17mm Width, 24000rpm Maximum Rotational Speed, 3440lbf Static Load Capacity, 5730lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6207-C3

Materi/Bahan: Steel

Diameter Lubang: 35  mm

Diameter Luar: 72  mm

Lebar Bearing:  17  mm

Kecepatan Rotasi Maksimum: 11000  RPM

Kapasitas Muatan Statis: 2599.084 kilograms

Kapasitas Muatan Dinamis: 1560.358 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Light” bearing design for use in limited space applications or for average loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Open bearing for lubrication applied in place

Deskripsi:

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design allows for lubricating the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6204-2RSR Radial Bearing, Single Row, ABEC 1 Precision, Double Sealed, Steel Cage, Normal Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 10000rpm Maximum Rotational Speed, 1500lbf Static Load Capacity, 2900lbf Dynamic Load Capacity

Bearing FAG 6204-2RSR Radial Bearing, Single Row, ABEC 1 Precision, Double Sealed, Steel Cage, Normal Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 10000rpm Maximum Rotational Speed, 1500lbf Static Load Capacity, 2900lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart:  6204-2RSR-L038

Materi/Bahan: steel

Diameter Lubang: 20  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 10000  RPM

Kapasitas Muatan Statis: 680.3886 kilograms

Kapasitas Muatan Dinamis: 1315.418 kilograms

Fitur Produk:

  • Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
  • Conforms to ABEC 1 precision standard for performance within a narrow range of variation
  • CN (normal) radial internal clearance for applications that do not involve thermal expansion or atypical precision
  • Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
  • Rubber seals on both sides of the bearing to keep lubricant in and contaminants out

Deskripsi:

The FAG single-row double-sealed radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a CN (normal) radial internal clearance for applications that do not involve thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has rubber seals on both sides of the bearing to keep lubricant in and contaminants out. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Bearing FAG 6000-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 10mm ID, 26mm OD, 8 mm Wide 34000rpm Maximum Rotational Speed, 441lbf Static Load Capacity, 1040lbf Dynamic Load Capacity

Bearing FAG 6000-C3 Deep Groove Ball Bearing, Single Row, Open, Steel Cage, C3 Clearance, Metric, 10mm ID, 26mm OD, 8 mm Wide 34000rpm Maximum Rotational Speed, 441lbf Static Load Capacity, 1040lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6000-C-C3

Materi/Bahan: steel

Diameter Lubang: 10  mm

Diameter Luar: 26  mm

Lebar Bearing: 8  mm

Kecepatan Rotasi Maksimum: 36000  RPM

Kapasitas Muatan Statis: 471.7361 kilograms

Kapasitas Muatan Dinamis: 200.034 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Very Light” bearing design for use in limited space applications where shaft sizes are relatively large and the loads are not substantial
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Open bearing for lubrication applied in place

Deskripsi:

This FAG Very Light 6000 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Very Light,” making it applicable for use in limited space applications where shaft sizes are large and the loads are not substantial, and it can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The open design makes it easy to lubricate the bearing in place. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6003 Radial Bearing, Single Row, ABEC 1 Precision, Open, Steel Cage, Normal Clearance, Metric, 17mm ID, 35mm OD, 10mm Width, 28000rpm Maximum Rotational Speed, 735lbf Static Load Capacity, 1340lbf Dynamic Load Capacity

Bearing FAG 6003 Radial Bearing, Single Row, ABEC 1 Precision, Open, Steel Cage, Normal Clearance, Metric, 17mm ID, 35mm OD, 10mm Width, 28000rpm Maximum Rotational Speed, 735lbf Static Load Capacity, 1340lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6003

Materi/Bahan: steel

Diameter Lubang: 17  mm

Diameter Luar: 35  mm

Lebar Bearing: 10  mm

Kecepatan Rotasi Maksimum: 28000  RPM

Kapasitas Muatan Statis: 333.3904 kilograms

Kapasitas Muatan Dinamis: 607.8138 kilograms

Fitur Produk:

  • Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
  • Conforms to ABEC 1 precision standard for performance within a narrow range of variation
  • CN (normal) radial internal clearance for applications that do not involve thermal expansion or atypical precision
  • Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
  • Open bearing for lubrication in place and for use in applications with little exposure to dirt, grime, debris, and other contaminants

Deskripsi:

The FAG single-row, open radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a CN (normal) radial internal clearance for applications that do not involve thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has an open configuration for lubrication in place and applications involving negligible exposure to dirt, grime, debris, and other contaminants. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Bearing FAG 6204-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 15000rpm Maximum Rotational Speed, 1470lbf Static Load Capacity, 2860lbf Dynamic Load Capacity

Bearing FAG 6204-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 20mm ID, 47mm OD, 14mm Width, 15000rpm Maximum Rotational Speed, 1470lbf Static Load Capacity, 2860lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6204-2Z-L038-C3

Materi/Bahan: steel

Diameter Lubang: 20  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 18000  RPM

Kapasitas Muatan Statis: 1297.274 kilograms

Kapasitas Muatan Dinamis: 666.7808 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Light” bearing design for use in limited space applications or for average loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Metal shields on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a metal shield on either side that is fastened to the outside ring and extends over the rolling elements. The shields assist in keeping out contaminants such as dirt and grime and also help to hold in lubricant applied during manufacturing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Bearing FAG 6307N Radial Bearing, Single Row, ABEC 1 Precision, Open, With Snap Ring Groove, Steel Cage, Normal Clearance, Metric, 35mm ID, 80mm OD, 21mm Width, 4300lbf Static Load Capacity, 7500lbf Dynamic Load Capacity

Bearing FAG 6307N Radial Bearing, Single Row, ABEC 1 Precision, Open, With Snap Ring Groove, Steel Cage, Normal Clearance, Metric, 35mm ID, 80mm OD, 21mm Width, 4300lbf Static Load Capacity, 7500lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6307-N

Materi/Bahan: steel

Diameter Lubang: 35  mm

Diameter Luar: 80  mm

Lebar Bearing: 21  mm

Kapasitas Muatan Statis: 1950.447 kilograms

Kapasitas Muatan Dinamis: 3401.943 kilograms

Fitur Produk:

  • Axially symmetric races to support radial loads while maintaining high speeds and rotational accuracy
  • Conforms to ABEC 1 precision standard for performance within a narrow range of variation
  • CN (normal) radial internal clearance for applications that do not involve thermal expansion or atypical precision
  • Steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise
  • Open bearing for lubrication in place and for use in applications with little exposure to dirt, grime, debris, and other contaminants

Deskripsi:

The FAG single-row, open radial bearing has symmetric races to support radial loads while maintaining high speeds and rotational accuracy. It conforms to the precision standard Annular Bearing Engineers Committee (ABEC) 1 for performance within a narrow range of variation, and it has a CN (normal) radial internal clearance for applications that do not involve thermal expansion. Its steel cage evenly spaces the rollers for even load distribution and prevents contact to reduce friction, vibrations, and noise. It has an open configuration for lubrication in place and applications involving negligible exposure to dirt, grime, debris, and other contaminants. This radial ball bearing is suitable for use in general purpose applications that primarily involve radial loads and minimal axial loads at relatively high rotational speeds. These include transmissions, motors, and pumps, among others.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Bearing FAG 6303-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 17mm ID, 47mm OD, 14mm Width, 16000 rpm Maximum Rotational Speed, 1460 lbf Static Load Capacity, 3050 lbf Dynamic Load Capacity

Bearing FAG 6303-2ZR-C3 Deep Groove Ball Bearing, Single Row, Double Shielded, Steel Cage, C3 Clearance, Metric, 17mm ID, 47mm OD, 14mm Width, 16000 rpm Maximum Rotational Speed, 1460 lbf Static Load Capacity, 3050 lbf Dynamic Load Capacity

Bearing FAG·

Merk: Bearing FAG

Nomor/Jenis Sparepart: 6303-2Z-L038-C3

Materi/Bahan: Steel

Diameter Lubang: 17  mm

Diameter Luar: 47  mm

Lebar Bearing: 14  mm

Kecepatan Rotasi Maksimum: 16000  RPM

Kapasitas Muatan Statis: 1383.457 kilograms

Kapasitas Muatan Dinamis:  662.2449 kilograms

Fitur Produk:

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Medium” bearing design for average to above average radial loads and light to average axial loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Metal shields on both sides of the bearing keep the lubricant in and contaminants out

Deskripsi:

This FAG Medium 6300 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and the balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Medium,” making it applicable for use with average to above average radial loads and light to average axial loads. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a metal shield on either side that fastens to the outside ring and extends over the rolling elements. The shields help keep out contaminants such as dirt and grime and also help to hold in lubricant applied during manufacturing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

 

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.