Bearing FAG

FAG 222S-203 Split Spherical Roller Bearing, Polyamide Cage, Normal Clearance, 2-3/16″ ID, 120mm OD, 55mm Width, 2800rpm Maximum Rotational Speed

FAG 222S-203 Split Spherical Roller Bearing, Polyamide Cage, Normal Clearance, 2-3/16″ ID, 120mm OD, 55mm Width, 2800rpm Maximum Rotational Speed

Bearing, Bearing FAG·

Product Description

This FAG split spherical roller bearing has a polyamide cage, a CN radial clearance, and a straight bore suitable for applications that support radial and oscillating axial loads and in which bearing replacement is difficult, such as in trough conveyors. The polyamide cage is lightweight, spaces the rollers for even load distribution, and prevents contact to reduce friction, vibration, and noise. This bearing’s inner and outer ring halves bolt together, allowing the bearing to be replaced without removing the shaft that the bearing supports. This roller bearing’s CN (normal) radial clearance is for applications where thermal expansion does not reduce clearance. The bearing’s straight bore fits conventional cylindrical shafts. This bearing has two rows of symmetrically arranged rollers oriented on a concave raceway, which allow self-realignment and compensate for static and dynamic alignment errors. The bearing has a maximum operating temperature of 392 degrees F. This roller bearing is intended for interchangeability and meets Deutsches Institut für Normung (DIN) standards for parts numbering, bearing dimensions, load ratings, tolerances, and clearances. It meets International Standards Organization (ISO) standards for hardening of bearing rollers and rings. This spherical roller bearing is suitable for use in material handling equipment.

Specifications

Main bearing dimensions ISO 15:1998
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances ISO 492:2002
Steel composition for inner and outer rings and rollers ISO 683-17
System for creating part numbers DIN 623-1

Roller bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All roller bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Two row split spherical roller bearing suitable for applications that support high radial and oscillating axial loads
  • Polyamide cage is lightweight and spaces the rollers for even load distribution and prevents contact to reduce friction, vibration, and noise
  • Inner and outer ring halves bolt together for ease of installation
  • CN (normal) radial clearance for applications where thermal expansion is not a factor
  • Straight bore fits conventional cylindrical shafts
Specifications for this item
Brand Name FAG Bearings
Part Number 222S-203
System of Measurement Inch/Metric
Bore Diameter 2-3/16  inches
Outside Diameter 120  mm
Overall Width 55  mm
Max Rotational Speed 2800  RPM
Static Load Capacity 37500  pounds
Dynamic Load Capacity 325000  pounds
EAN 4012801478519
Item Weight 5.07 pounds
Number of Items 1
UNSPSC Code 31171505
FAG 51128 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 140mm ID, 180mm OD, 31mm Width, 1800rpm Maximum Rotational Speed, 90000lbf Static Load Capacity, 25000lbf Dynamic Load Capacity

FAG 51128 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 140mm ID, 180mm OD, 31mm Width, 1800rpm Maximum Rotational Speed, 90000lbf Static Load Capacity, 25000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51128
System of Measurement Metric
Bore Diameter 140  mm
Outside Diameter 180  mm
Overall Width 31  mm
Max Rotational Speed 1800  RPM
Static Load Capacity 90000  pounds
Dynamic Load Capacity 25000  pounds
EAN 4012801513814
Item Weight 5 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 51209 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 73mm OD, 20mm Width, 3600rpm Maximum Rotational Speed, 18000lbf Static Load Capacity, 8800lbf Dynamic Load Capacity

FAG 51209 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 73mm OD, 20mm Width, 3600rpm Maximum Rotational Speed, 18000lbf Static Load Capacity, 8800lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51209
System of Measurement Metric
Bore Diameter 45  mm
Outside Diameter 73  mm
Overall Width 20  mm
Max Rotational Speed 3600  RPM
Static Load Capacity 18000  pounds
Dynamic Load Capacity 8800  pounds
EAN 4012801162395
Item Weight 10 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 53316 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 80mm ID, 140mm OD, 47.6mm Width, 3600rpm Maximum Rotational Speed, 80000lbf Static Load Capacity, 36000lbf Dynamic Load Capacity

FAG 53316 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 80mm ID, 140mm OD, 47.6mm Width, 3600rpm Maximum Rotational Speed, 80000lbf Static Load Capacity, 36000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53316
System of Measurement Metric
Bore Diameter 80  mm
Outside Diameter 140  mm
Overall Width 47.6  mm
Max Rotational Speed 3600  RPM
Static Load Capacity 80000  pounds
Dynamic Load Capacity 36000  pounds
EAN 4012801199537
Item Weight 6.3 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 53320 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 100mm ID, 170mm OD, 59.2mm Width, 1500rpm Maximum Rotational Speed, 127000lbf Static Load Capacity, 52000lbf Dynamic Load Capacity

FAG 53320 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 100mm ID, 170mm OD, 59.2mm Width, 1500rpm Maximum Rotational Speed, 127000lbf Static Load Capacity, 52000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53320
System of Measurement Metric
Bore Diameter 100  mm
Outside Diameter 170  mm
Overall Width 59.2  mm
Max Rotational Speed 1500  RPM
Static Load Capacity 127000  pounds
Dynamic Load Capacity 52000  pounds
EAN 4012801323109
Item Weight 11.24 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 51214 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 70mm ID, 105mm OD, 27mm Width, 2800rpm Maximum Rotational Speed, 35500lbf Static Load Capacity, 14600lbf Dynamic Load Capacity

FAG 51214 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 70mm ID, 105mm OD, 27mm Width, 2800rpm Maximum Rotational Speed, 35500lbf Static Load Capacity, 14600lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51214
System of Measurement Metric
Bore Diameter 70  mm
Outside Diameter 105  mm
Overall Width 27  mm
Max Rotational Speed 2800  RPM
Static Load Capacity 35500  pounds
Dynamic Load Capacity 14600  pounds
EAN 4012801197922
Item Weight 1.79 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 52406 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 20mm ID, 70mm OD, 52mm Width

FAG 52406 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 20mm ID, 70mm OD, 52mm Width

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52406
System of Measurement Metric
Bore Diameter 20  mm
Outside Diameter 70  mm
Overall Width 52  mm
EAN 4012801515450
Number of Items 1
UNSPSC Code 31171552
FAG 52311 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 105mm OD, 64mm Width, 2400rpm Maximum Rotational Speed, 46500lbf Static Load Capacity, 23200lbf Dynamic Load Capacity

FAG 52311 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 105mm OD, 64mm Width, 2400rpm Maximum Rotational Speed, 46500lbf Static Load Capacity, 23200lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52311
System of Measurement Metric
Bore Diameter 45  mm
Outside Diameter 105  mm
Overall Width 64  mm
Max Rotational Speed 2400  RPM
Static Load Capacity 46500  pounds
Dynamic Load Capacity 23200  pounds
EAN 4012801322416
Item Weight 5.53 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 52212 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 50mm ID, 95mm OD, 46mm Width, 3000rpm Maximum Rotational Speed, 31500lbf Static Load Capacity, 14000lbf Dynamic Load Capacity

FAG 52212 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 50mm ID, 95mm OD, 46mm Width, 3000rpm Maximum Rotational Speed, 31500lbf Static Load Capacity, 14000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52212
System of Measurement Metric
Bore Diameter 50  mm
Outside Diameter 95  mm
Overall Width 46  mm
Max Rotational Speed 3000  RPM
Static Load Capacity 31500  pounds
Dynamic Load Capacity 14000  pounds
EAN 4012801322256
Number of Items 1
UNSPSC Code 31171552
FAG 6214-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 70mm ID, 125mm OD, 24mm Width, 3400rpm Maximum Rotational Speed, 10100lbf Static Load Capacity, 13600lbf Dynamic Load Capacity

FAG 6214-2RSR-C3 Deep Groove Ball Bearing, Single Row, Double Sealed, Steel Cage, C3 Clearance, Metric, 70mm ID, 125mm OD, 24mm Width, 3400rpm Maximum Rotational Speed, 10100lbf Static Load Capacity, 13600lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG Light 6200 Series single row deep groove ball bearing with a sheet steel cage supports radial loads and axial loads in both directions. It is also suitable for high speed applications. This bearing has a C3 radial internal clearance designation to indicate that the radial slack between the inner and outer rings is greater than the standard CN (normal) clearance. It allows for thermal expansion as the bearing supports radial loads and its balls, operating in the deep raceway geometry, reduce rotational friction. This bearing is rated “Light,” making it applicable for average radial loads and light axial loads where space is tight and shaft diameters are relatively large. It can be used to a maximum operating temperature of 120 degrees C/248 degrees F. The inner and outer rings and balls are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. The bearing has a rubber seal on either side that is fastened to the outside ring, and extends over the rolling elements and to make contact with the inside ring, keeping out contaminants such as dirt and grime. The seals also hold lubricant applied during manufacturing that will last the lifetime of the bearing. This deep groove ball bearing is for use in various applications such as transmissions, motors, pumps, bicycles, and inline skates, among others.

Specifications Met

Main bearing dimensions DIN 625-1
Basic dynamic load ratings DIN ISO 281
C3 radial internal clearance DIN 620-4 (ISO 5 753)
Shaft and housing tolerances ISO 286
Through-hardening steel for inner and outer rings ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. Founded in 1883, FAG is based in Schweinfurt, Germany.

Product Features

  • Deep groove geometry for high speeds and supporting both radial and axial loads
  • “Light” bearing design for use in limited space applications or for average loads
  • C3 radial clearance allows thermal expansion for continuous operating temperatures up to 120 degrees C/248 degrees F
  • Sheet steel cage evenly spaces balls for reduced friction, vibration, and noise
  • Rubber seals on both sides of the bearing keep the lubricant in and contaminants out
Specifications for this item
Brand Name FAG Bearings
Part Number 6214-2RSR-C3
Material Type Steel
System of Measurement Metric
Bore Diameter 70  mm
Outside Diameter 125  mm
Overall Width 24  mm
Max Rotational Speed 6000  RPM
Static Load Capacity 13600  pounds
Dynamic Load Capacity 10100  pounds
Specification Met DIN 620-4/DIN 623-1/DIN 625-1/DIN ISO 281/EN 10139/ISO 281/ISO 286/ISO 683-17/SAE J403
EAN 4012801077347
Number of Items 1
UNSPSC Code 31171504