Bearing

Bearing dalam Bahasa Indonesia berarti bantalan. Dalam ilmu mekanika bearing adalah sebuah elemen mesin yang berfungsi untuk membatasi gerak relatif antara dua atau lebih komponen mesin agar selalu bergerak pada arah yang diinginkan. Bearing menjaga poros (shaft) agar selalu berputar terhadap sumbu porosnya, atau juga menjaga suatu komponen yang bergerak linier agar selalu berada pada jalurnya.

Image result for bearing adalah

Bantalan merupakan salah satu bagian dari elemen mesin yang memegang peranan cukup penting karena fungsi dari bantalan yaitu untuk menumpu sebuah poros agar poros dapat berputar tanpa mengalami gesekan yang berlebihan. Bantalan harus cukup kuat untuk memungkinkan poros serta elemen mesin lainnya bekerja dengan baik.

Bearing atau laher adalah komponen sebagai bantalan untuk membantu mengurangi gesekan peralatan berputar pada poros/as. Bearing atau laher ini biasanya berbentuk bulat. Bearing di mobil dipasang pada as roda dan ditempat-tempat yang berputar lainnya. Tujuan dari bantaran balock untuk mengurangi gesekan rotasi dan mendukung radial dan aksial beban.

 

FAG 51309 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 85mm OD, 28mm Width, 3000rpm Maximum Rotational Speed, 31500lbf Static Load Capacity, 17000lbf Dynamic Load Capacity

FAG 51309 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 45mm ID, 85mm OD, 28mm Width, 3000rpm Maximum Rotational Speed, 31500lbf Static Load Capacity, 17000lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51309
System of Measurement Metric
Bore Diameter 45  mm
Outside Diameter 85  mm
Overall Width 28  mm
Max Rotational Speed 3000  RPM
Static Load Capacity 31500  pounds
Dynamic Load Capacity 17000  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162500
Number of Items 1
UNSPSC Code 31171552
FAG 52209 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 35mm ID, 73mm OD, 37mm Width, 3600rpm Maximum Rotational Speed, 18000lbf Static Load Capacity, 8800lbf Dynamic Load Capacity

FAG 52209 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 35mm ID, 73mm OD, 37mm Width, 3600rpm Maximum Rotational Speed, 18000lbf Static Load Capacity, 8800lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52209
System of Measurement Metric
Bore Diameter 35  mm
Outside Diameter 73  mm
Overall Width 37  mm
Max Rotational Speed 3600  RPM
Static Load Capacity 18000  pounds
Dynamic Load Capacity 8800  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162654
Item Weight 1.37 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 53214 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 70mm ID, 105mm OD, 28.8mm Width, 2800rpm Maximum Rotational Speed, 35500lbf Static Load Capacity, 14600lbf Dynamic Load Capacity

FAG 53214 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 70mm ID, 105mm OD, 28.8mm Width, 2800rpm Maximum Rotational Speed, 35500lbf Static Load Capacity, 14600lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53214
System of Measurement Metric
Bore Diameter 70  mm
Outside Diameter 105  mm
Overall Width 28.8  mm
Max Rotational Speed 2800  RPM
Static Load Capacity 35500  pounds
Dynamic Load Capacity 14600  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801199308
Item Weight 1.76 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 53315 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 75mm ID, 135mm OD, 48.1mm Width, 3800rpm Maximum Rotational Speed, 80000lbf Static Load Capacity, 36500lbf Dynamic Load Capacity

FAG 53315 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 75mm ID, 135mm OD, 48.1mm Width, 3800rpm Maximum Rotational Speed, 80000lbf Static Load Capacity, 36500lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53315
System of Measurement Metric
Bore Diameter 75  mm
Outside Diameter 135  mm
Overall Width 48.1  mm
Max Rotational Speed 3800  RPM
Static Load Capacity 80000  pounds
Dynamic Load Capacity 36500  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801323093
Item Weight 6 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 52305 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 20mm ID, 52mm OD, 34mm Width, 4300rpm Maximum Rotational Speed, 12500lbf Static Load Capacity, 7800lbf Dynamic Load Capacity

FAG 52305 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 20mm ID, 52mm OD, 34mm Width, 4300rpm Maximum Rotational Speed, 12500lbf Static Load Capacity, 7800lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Specifications for this item
Brand Name FAG Bearings
Part Number 52305
System of Measurement Metric
Bore Diameter 20  mm
Outside Diameter 52  mm
Overall Width 34  mm
Max Rotational Speed 4300  RPM
Static Load Capacity 12500  pounds
Dynamic Load Capacity 7800  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162678
Number of Items 1
UNSPSC Code 31171552

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
FAG 53313 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 65mm ID, 115mm OD, 39.4mm Width, 2200rpm Maximum Rotational Speed, 49000lbf Static Load Capacity, 23600lbf Dynamic Load Capacity

FAG 53313 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 65mm ID, 115mm OD, 39.4mm Width, 2200rpm Maximum Rotational Speed, 49000lbf Static Load Capacity, 23600lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53313
System of Measurement Metric
Bore Diameter 65  mm
Outside Diameter 115  mm
Overall Width 39.4  mm
Max Rotational Speed 2200  RPM
Static Load Capacity 49000  pounds
Dynamic Load Capacity 23600  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801199520
Item Weight 3.55 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 51313 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 65mm ID, 115mm OD, 36mm Width, 2200rpm Maximum Rotational Speed, 49000lbf Static Load Capacity, 23600lbf Dynamic Load Capacity

FAG 51313 Grooved Race Thrust Bearing, Single Row, Open, 90° Contact Angle, Steel Cage, Metric, 65mm ID, 115mm OD, 36mm Width, 2200rpm Maximum Rotational Speed, 49000lbf Static Load Capacity, 23600lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row thrust ball bearing has grooved raceways, a 90-degree contact angle, a steel cage, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 51313
System of Measurement Metric
Bore Diameter 65  mm
Outside Diameter 115  mm
Overall Width 36  mm
Max Rotational Speed 2200  RPM
Static Load Capacity 49000  pounds
Dynamic Load Capacity 23600  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801198226
Number of Items 1
UNSPSC Code 31171552
FAG 53311 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 55mm ID, 105mm OD, 39.3mm Width, 2400rpm Maximum Rotational Speed, 46500lbf Static Load Capacity, 23200lbf Dynamic Load Capacity

FAG 53311 Self-Aligning Thrust Bearing, Single Row, 90° Contact Angle, Open, Metric, 55mm ID, 105mm OD, 39.3mm Width, 2400rpm Maximum Rotational Speed, 46500lbf Static Load Capacity, 23200lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG single-row self-aligning thrust ball bearing has a 90-degree contact angle and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in one direction and no radial loads. This deep-groove thrust ball bearing consists of a spherical housing locating washer (ring), a shaft locating washer, and a ball and cage assembly. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The bearing is self-aligning with a spherical-shaped housing washer that helps compensate for static angular misalignments between the shaft and housing. The single-row design supports thrust loads in a single direction and tolerates axial deflection, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 711/ISO 104
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Single direction, deep-groove thrust ball bearing for applications that support heavy axial loads in one direction
  • Self-aligning bearing with sphered housing rings to compensate for static angular misalignments between the shaft and housing
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 53311
System of Measurement Metric
Bore Diameter 55  mm
Outside Diameter 105  mm
Overall Width 39.3  mm
Max Rotational Speed 2400  RPM
Static Load Capacity 46500  pounds
Dynamic Load Capacity 23200  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 104/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801323079
Item Weight 3.11 pounds
Number of Items 1
UNSPSC Code 31171552
FAG 52208 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 30mm ID, 68mm OD, 36mm Width, 3800rpm Maximum Rotational Speed, 10600lbf Dynamic Load Capacity

FAG 52208 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 30mm ID, 68mm OD, 36mm Width, 3800rpm Maximum Rotational Speed, 10600lbf Dynamic Load Capacity

Bearing, Bearing FAG·
Specifications for this item
Brand Name FAG Bearings
Part Number 52208
System of Measurement Metric
Bore Diameter 30  mm
Outside Diameter 68  mm
Overall Width 36  mm
Max Rotational Speed 3800  RPM
Dynamic Load Capacity 10600  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801162647
Number of Items 1
UNSPSC Code 31171552

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

FAG 52310 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 40mm ID, 95mm OD, 58mm Width, 2800rpm Maximum Rotational Speed, 39000lbf Static Load Capacity, 19600lbf Dynamic Load Capacity

FAG 52310 Double Direction Thrust Bearing, Double Row, Open, 90° Contact Angle, Steel Cage, Metric, 40mm ID, 95mm OD, 58mm Width, 2800rpm Maximum Rotational Speed, 39000lbf Static Load Capacity, 19600lbf Dynamic Load Capacity

Bearing, Bearing FAG·

Product Description

This FAG double-row, double-direction thrust ball bearing has a 90-degree contact angle, steel cages, and an open construction. It is suitable for moderate-speed applications that support heavy axial loads in both directions and no radial loads. This deep-groove thrust ball bearing consists of two housing locating washers (rings), a shaft locating washer, and two ball and cage assemblies. The washers have grooved raceways that conform to the balls rotating between them, allowing higher speeds and thrust bearing capacity than bearings with flat raceways. The double-row design supports bidirectional thrust loads with minimum axial deflection, increasing the load carrying capacity, and the open construction allows for the bearing to be lubricated in place. This bearing has a 90-degree contact angle in which the ball and inner and outer raceway contact points are on a plane parallel to the axial load, which enables the bearing to receive high axial force. The balls and washers are made of a low-alloy, through-hardened chromium steel for durability, heat tolerance, and resistance to deformity under heavy loads, and the sheet steel cage prevents the balls from coming into contact with each other during use, reducing friction, vibration, and noise. This bearing is separable so it mounts more easily than nonseparable bearings because its components can be installed independently. It can be used at operating temperatures from -30 degrees C to 150 C (-22 degrees F to 302 F). This thrust ball bearing has a PN (normal) tolerance class rating for dimensional accuracy and is suitable for applications including machine tool drive shafts, automotive steering gears and clutches, rotary tables, outboard motor propellers, and household appliances.

Specifications

Main bearing dimensions DIN 715
Basic dynamic load ratings DIN ISO 281
Dimensional and geometric tolerances DIN 620-3 (ISO 199), tolerance class PN
Through-hardening steel for inner and outer rings and rollers ISO 683-17
Steel strip for cage EN 10139, SAE J403
Load carrying capacity and life DIN ISO 281 Appendix 1
System for creating part numbers for rolling bearings DIN 623-1

Rolling bearings use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads. These elements can be one of the following types: ball, cylindrical, spherical, barrel, needle, spindle, or tapered. All rolling bearings are open, shielded, or sealed. Sealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use. The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.

FAG manufactures a variety of bearings that meet International Organization for Standardization (ISO) and Deutsches Institut für Normung (DIN) standards for quality assurance. The company, founded in 1883, is based in Schweinfurt, Germany.

Product Features

  • Double direction, deep-groove thrust ball bearing for moderate speed applications that support heavy axial loads in both directions
  • Open bearing for lubrication applied in place
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads
  • Sheet steel retainer evenly spaces rollers for reduced friction, vibration, and noise
  • Grooved raceways for higher speeds and thrust-bearing capacity than flat washers
Specifications for this item
Brand Name FAG Bearings
Part Number 52310
System of Measurement Metric
Bore Diameter 40  mm
Outside Diameter 95  mm
Overall Width 58  mm
Max Rotational Speed 2800  RPM
Static Load Capacity 39000  pounds
Dynamic Load Capacity 19600  pounds
Specification Met DIN 623-1/DIN ISO 281/EN 10139/ISO 199/ISO 281/ISO 683-17/SAE J403
EAN 4012801198882
Number of Items 1
UNSPSC Code 31171552